Fire Alarm Battery Standby Calculator

Last reviewed: by Sarwar Islam

Work out the battery a fire alarm panel needs to keep running when the mains fails. Add the control panel, detectors, sounders and other loads, choose a 24 hour or 72 hour standby period and the alarm time, and the calculator gives the capacity in amp-hours and the next common battery size, using the BS 5839-1 Annex E method or the NFPA 72 method, with a drawing that shows where the capacity goes.

Techubox

Fire Alarm Battery Standby Calculator

Add the panel and devices, pick 24 h or 72 h standby, and get the battery Ah you need and the next standard size.

FreeNo sign-upBS 5839-1 Annex ENFPA 72 optionLive drawing
Standard
Panel battery voltage
Standby time
Alarm time
Tap to add devices
    ⚙ Advanced options

    The defaults follow the standard you chose. Use the battery maker’s figures where they differ.

    ×
    ×
    h
    min

    🔋 Where the capacity goes

    Battery capacity breakdown

      📊 Details: currents and notes

      Devices on the battery supply

      🧮 Calculation steps
      📋 Common battery sizes and what they cover

      Common 12 V sealed lead-acid (VRLA) capacities at the 20-hour rate. Check the range your battery supplier and your panel’s charger allow: each panel has a maximum battery size it can recharge in the required time.

      🎓 How to use this tool
      1. Tap BS 5839-1 or NFPA 72. The standby time, alarm time and factors change to that standard’s usual values.
      2. Tap 12 V or 24 V to match your panel, then the standby time (24, 48 or 72 h) and the alarm time.
      3. Tap the device buttons to add the panel, detectors, sounders and other loads. Enter each device’s standby and alarm current in mA from its data sheet, and the quantity.
      4. Read the answer card: the capacity you need and the next standard battery size. Green leaves some headroom, amber is a tight fit, red means no single common size is large enough.
      5. Open Advanced options to change the ageing factor, the alarm de-rating factor or the times.

      Standards & assumptions

      BS 5839-1:2025 Annex E: Cmin = 1.25 × (T1 × I1 + D × I2 × T2), in Ah at the 20-hour rate and 20 °C, where I1 is the standby current, T1 the standby time, I2 the alarm current, T2 the alarm time in hours, 1.25 the ageing factor and D the alarm de-rating factor (1.75 unless the battery maker gives another figure). NFPA 72 asks for 24 hours of standby followed by 5 minutes of alarm (15 minutes for emergency voice alarm communication and in-building mass notification), with a margin on top, which this tool treats as the same formula with D = 1 and an editable margin. Common battery sizes are 12 V sealed lead-acid; a 24 V panel uses two in series, each at the full calculated Ah. These documents give guidance; check the current edition and your local authority, and use the panel maker’s battery calculation where it gives one. The tool does not check the panel’s charger limit, the recharge time or the voltage at the end of discharge.

      Sizing a UPS or a general battery backup instead? Use the UPS & Battery Backup Calculator. · Techubox Engineering Tools · techubox.com/tools

      To download and print this tool without a watermark, please log in and request approval.

      How to size fire alarm standby batteries with this calculator

      A fire alarm panel runs from the mains and keeps its batteries in reserve. If the mains fails, the batteries must hold the whole system up in its normal quiet state for the standby period, and then run the sounders and beacons at full alarm load for the alarm period. Too small a battery means the system goes dead during a long power cut or fails in the first minutes of an alarm. The calculator turns your device list into one capacity figure and a battery size.

      1. Tap BS 5839-1 or NFPA 72. The standby time, alarm time and factors switch to that standard’s usual values.
      2. Tap 12 V or 24 V to match the panel, then the standby time and the alarm time.
      3. Tap the device buttons to add the panel, detectors, sounders and other loads. For each line enter the standby and alarm current in milliamps from the data sheet, and the quantity.
      4. Read the answer card: the required capacity, the next common battery size and how much headroom it leaves.
      5. Open Advanced options to change the ageing factor, the alarm de-rating factor D or either time.

      The formula explained

      BS 5839-1:2025 Annex E gives the minimum capacity Cmin in amp-hours at the 20 hour rate and 20 °C as Cmin = 1.25 × (T1 × I1 + D × I2 × T2). I1 is the total standby (quiescent) current in amps and T1 the standby time in hours. I2 is the total alarm current and T2 the alarm time in hours, so 30 minutes is 0.5. The 1.25 is the ageing factor: a battery loses capacity as it gets older, and the sizing leaves room for that. D is a de-rating factor on the alarm term, normally 1.75 unless the battery maker gives another figure, because a battery delivers less than its rated amp-hours when it is discharged quickly.

      The NFPA 72 method is the same arithmetic with a different set of numbers: 24 hours of standby, then 5 minutes of alarm (15 minutes for emergency voice alarm communication and in-building mass notification), with no de-rating factor and a safety margin on the total. That margin is at least 20% in the 2010 to 2019 editions and 25% in the 2022 edition, so the tool lets you edit it. Edition and clause numbers move, so state which edition your project adopts.

      Worked example: BS 5839-1, 24 hours plus 30 minutes

      A panel and devices draw 250 mA in standby and 750 mA in alarm. The standby part is 0.25 × 24 = 6.00 Ah. The alarm part is 1.75 × 0.75 × 0.5 = 0.656 Ah. Together 6.656 Ah, and with the 1.25 ageing factor Cmin = 8.32 Ah. The next common size is 12 Ah, which leaves 31% headroom. On a 24 V panel you fit two 12 V 12 Ah batteries in series.

      Worked example: NFPA 72, 24 hours plus 5 minutes

      A system draws 450 mA in standby and 2.1 A in alarm. Standby: 0.45 × 24 = 10.8 Ah. Alarm: 2.1 × 5/60 = 0.175 Ah. The subtotal is 10.975 Ah. With a 20% margin that is 13.17 Ah; with the 25% margin of the 2022 edition it is 13.72 Ah. Either way a 17 Ah battery is the next common size.

      Worked example: a 72 hour standby

      Some projects ask for 48 or 72 hours, for example where a fault could go unnoticed in an unattended building. With the same 250 mA and 750 mA loads, 72 hours of standby gives 0.25 × 72 = 18 Ah, plus the 0.656 Ah alarm part, times 1.25 = 23.32 Ah. The next size is 24 Ah, and the calculation sits at 97% of it, so the tool shows amber. The standby load dominates, which is why a longer standby period grows the battery so fast.

      Where to get the currents

      Use the data sheet of each device, in milliamps, and add every load that the panel’s batteries feed: the panel itself (usually the largest part of the standby current), detectors, interface modules, isolators, remote annunciators and any communicator. Sounders and beacons dominate the alarm current, so use the figure for the volume or flash setting you will actually fit. Where a data sheet says “less than 80 mA”, use 80 mA. The example values in the tool come from published Context Plus panel and device data sheets; replace them with your own models.

      Alarm current is the current with everything that operates in alarm switched on. A common conservative design assumption is all sounders and beacons operating, plus the panel and detectors at their alarm draw; state your assumption in the calculation note.

      Battery sizes and 24 V panels

      Panel batteries are normally 12 V sealed lead-acid (VRLA) in flame-retardant cases. Common capacities include 1.2, 2.8, 7, 12, 17, 18, 24, 26, 38 and 65 Ah. A 24 V panel uses two 12 V batteries in series. The amp-hours do not add in series, so each battery must have the full calculated capacity. Never mix batteries of different capacity or age in one string. Each panel also has a maximum battery size its charger can recharge in the required time; if your result is above it, the answer is a separate battery-backed power supply, not a bigger battery in the same cabinet.

      Which standard applies

      BS 5839-1 is used for UK projects and many export projects that follow the European route with EN 54 equipment. NFPA 72 is used in the US and on many projects in the Gulf and elsewhere that adopt NFPA. The two give different batteries for the same equipment, mostly because BS 5839-1 uses a longer alarm period. Pick one route for the whole project. For the wider differences see our comparison BS 5839 vs NFPA 72. These documents give guidance; check the current edition and your local authority, and use the panel maker’s battery calculation where it provides one.

      Common mistakes

      • Fitting the battery that came with the panel without a calculation, or copying a size from another job.
      • Leaving out remote annunciators, relay modules or a communicator that the panel supplies.
      • Using a 5 minute alarm period for a voice evacuation system that needs 15 minutes.
      • Forgetting the ageing factor or margin, or mixing the NFPA margin with the BS 5839-1 factors.
      • Splitting the Ah between the two batteries of a 24 V pair instead of using the full figure for each.
      • Adding sounders after handover without recalculating.
      • Putting the batteries in a hot cabinet: heat shortens their life well below the design figure.

      Frequently asked questions

      How long must fire alarm batteries last?

      Under BS 5839-1 the usual duty is 24 hours of standby plus 30 minutes of alarm, longer where the building is unattended. NFPA 72 asks for 24 hours of standby plus 5 minutes of alarm, or 15 minutes for voice systems. A project specification or the authority can ask for more.

      Why is the BS 5839-1 result larger than NFPA 72?

      The alarm period is 30 minutes instead of 5, the alarm load is multiplied by D, and the ageing factor is 1.25. With a large standby load the difference is small; with a large sounder load it is big.

      Can I use any 12 V battery?

      No. Use a sealed lead-acid standby battery of the capacity you calculate, in a case rated for fire alarm use, and follow the panel maker’s list of approved batteries. A car battery is the wrong type.

      Does this replace the manufacturer’s calculator?

      No. The panel maker’s sheet knows the panel’s own standby current, its charger limit and any approved battery range. Use this tool to check the result or to plan before you choose a panel.

      How is this different from the UPS & Battery Backup Calculator?

      The UPS & Battery Backup Calculator sizes a UPS or battery bank for general equipment by watts and runtime. This tool sizes the standby batteries inside a fire alarm panel by standby and alarm currents, with the ageing and de-rating factors the fire alarm standards use.

      To lay out the system itself, see the Fire Alarm Design Tool and the Conventional Fire Alarm Design Tool, and the guide How to Design a Fire Alarm System.

      Scroll to Top